Used VEECO FPP 5000 #128113 for sale
It looks like this item has already been sold. Check similar products below or contact us and our experienced team will find it for you.
Tap to zoom


Sold
ID: 128113
Four point system
Compact integral probe and display
Microprocessor based electronics
Automatic ranging
Four selectable displays
Sheet Resistivity
V/I
Bulk resistivity of a slice with a known thickness
Thickness in, A, MILS, or microns of a slice or layer with a known bulk resistivity
Keyboard Programming of slice or layer thickness or bulk resistivity
Automatically performs a reverse and forward measurement each time the cover is closed
RETEST button allows additional measurements without disturbing the probes
Automatically holds the last reading after the probe is released and until the next measurement is made
Error code displays indicate improper operation, readings and electronics
Extended measurement range displays sheet resistivity up to 450k ohm/sq and down to a resolution of .001 milliohm/SQ
High accuracy of 0.5% of reading on all reading between 5 milliohm to 5 k ohm. No more than +/- 8.0% at the extreme limits of the range
Self test circuitry built in to determine if a fault is present
Self calibration and zero circuitry assures high accuracy in all but extreme ranges
Index substrate holder allows repeatable probe positioning on the substrate
Probe up permits repeatable measurements independent of operator force and substrate thickness
Integral RFI and light shielding for high resistivity measurements
Plug in probe head adaptors make probe head changing convenient and non critical
Typing mode determines N and P typing for most semiconductor substrates or layers
Penetration permits high energy pulse to be applied for the purpose of breaking through thin oxide layers
Penetrate function can be disabled by means of internal switches
Automatic calculation of correction factors to compensate for probe tip spacing variations
Back lit front panel indicates only the units applicable for the mode of operation chosen
Electrical Specifications:
The FPP-5000 requires an input power of 115/230 VAC +/- 10%, 50/60 Hz, at approximately 30 watts
Geometric Correction Range:
Based on the 2 configuration technique. Displays if calculated geometric correction is between 4.18 and 4.82
Calculated values above and below results in a flashing display in display SHEET, SLICE, and THICK
If as a result of the calculation, the intermediate results are negative, the display will indicate E 07.
Optional RS-232C Interface: Output on 25 pin female subminiature "D" connector
Selectable Baud Rate: 9600, 4800, 2400, 1200, 300, 150
Optional Hand Held Probe Head: For testing wafers over 6" in Diameter. Comes with six foot cable. Specify probe head when ordering.
VEECO FPP 5000 is a high-precision prober designed for advanced probing solutions. VEECO FPP-5000 is designed for use in a wide range of industries, including semiconductors, optics, and electronics. It features a number of features and technologies that allow FPP 5000 to achieve greater accuracy and resolution, and provide a reliable means for testing and inspection. FPP-5000 starts with a precision mechanism and advanced software. It utilizes a precision XYZ linear, motorized stage. The stage is driven by separately servo-controlled, brushless direct current (DC) motors providing a maximum travel speed of 400mm/s. This allows for fast and accurate scanning, resulting in a high throughput. The prober also features a number of technologies that further enhance the accuracy of the data acquisition. These include a monochromator-controlled focused laser spot with either an 8x or 4x microscope objective for resolution down to microns; a high numerical aperture (NA) lens to achieve an ultra-low Z-axis resolution; and a high resolution digital charge coupled device (CCD) camera. This combination of technologies provides the capability to rapidly capture and analyze images at an unparalleled level of accuracy. The software that drives VEECO FPP 5000 also plays a critical role in its performance. It is capable of controlling the high-speed stage movements, as well as the multiple technologies that allow for high-resolution imaging. The scanning software can be used to select data acquisition area, resolution, beam focus, and other scanning parameters. VEECO FPP-5000 is an ideal choice for users who require a reliable and accurate prober for advanced probing solutions. Its precision mechanical design and high-tech combination of imaging technologies make it well suited for a wide variety of industries. Additionally, its advanced software allows FPP 5000 to be used with a range of applications, ensuring optimal results are achieved.
There are no reviews yet