Pcb Solder Machines

Fluxer / gradient Air: 6 Bar 480V, 50/60Hz, 12 KVA 1999 vintage.

Wave solder machine External Spray Fluxer (3) bottom convection preheaters (3) upper reflector panels Lambda Wave Chip wave available Computer controlled L-type and V-grove combo finger configuration Finger cleaner.

Reflow checker.

Wave solder machine 2004 vintage.

Lead free dual wave solder machine Left to right 16" finger conveyor Spray fluxer (2) Bottom convection pre-heat sections 2007 vintage.

Wave solder machines Flexible titanium fingers: Yes Finger cleaner: Yes (2) Bottom Heaters IR topside heater OP-BASE-VC Vectra Base Machine OP-N2ROT-VC Nitrogen Rotary Chip Nozzle OP-FLXI-VC Flexible Intermix fingers OP-MROLL-VC Motorized Rollout/Jack OP-FCLR-VC Finger Cleaner OP-WFEED-WS Wire Feeder OP-MWTH-VC Motorized Width Adjust OP-HGTSNR-EC Wave Height Sensor OP-VEC-VC Vecta Heater OP-OUTPUT-WS Output Photocell OP-SLCTSPRY-VC SelectaSpray Fluxer OP-LOCKS-VC Front Hood Interlocks OP-EXTFLX-WS External Fluxer Cabinet OP-SMEMA-WS SMEMA Interface OP-LEADFREE-VC Lead Free Capability OP-MNLS-AS English CD Manual OP-N2PLS-VC Contour Plus System QWS-1121165-02 Rear Door Interlocks 2001-2002 vintage.

HASL system.

Desoldering system.

Solderability and wetability tester Dip tin / lead Solder temperature: 0 – 350 °c Dipping speed: 0 – 30 mm/s Immersion depth: 0 – 30 mm/s Dwell time: 0 – 30 s Maximum component weight: 40 g Force sampling frequency: 1,000 hz Globule sizes: 1 mm, 2 mm, 3.2 mm or 4 mm Solder bath diameter: 60 mm Solder bath capacity: 1 kg Power supply: 240 v, 50 hz or 110 v, 60 hz Power consumption: 750 w Operation system: DOS Currently in storage.

Wave solder machine Extended rails Spray fluxer in external cabinet (2) Bottomside convections Contour wave Rotary chip wave 18" process width Motorized pot with jacking stand L to R process flow Computer controlled 2002 vintage.

Soldering machine.

Soldering system.

Leaded wave solder machine, Temperature: 450°F Foam fluxer 18" Dual wave Ultrafil nozzle Finger cleaner IR Bottom side preheater, convection IR Topside pre-heat and heat Left to Right Cast pot: lead-free capable N2: no 2001 vintage.

Wave solder machine, 8" Pallet conveyor Temperature maximum: 350°C Fluxer: Slide out fluxer with overflow tray Stainless steel reservoir and nozzle Self-contained onboard air compressor Preheater: (2) Preheaters with total 6.0 kW and 38" Heat tunnel effect Solder module: Fully dry wave No oil intermix Stainless steel solder pot Solder level monitor with alarm Control: Microprocessor based onboard computer SPC reporting via RS-232 serial interface Computer parmeter storage unit Flux and wave interval sensor Safety: Status light tower Low temperature solder pump disable Circuit breakers in lieu of fuses on all power lines Screw locked electrical cabinet Memory battery back-up.

Rework stations Model 4 & 5 Options: Board cooling Site cleaning nozzle Fume extraction option not included 2007 vintage.

Rework Station Lead Free Fine Pitch Component Handling Closed Loop Heating Process Top and Bottom Side Heating Site Cleaning Image for component alignment Integrated Dispensing System Top heater: 2000W Infra-red (IR) bottom heating technology Bottom heating panel: 19" x 19", (4) independently programmable heating zones, 6000W Programmable cold air injection and linear air knife Converted to 208-220V (Air Vac), Original Zevac 400V 2007 vintage.

Selective solder machine MultiWave Solder Pot X-Y fluxer Inline preheat SMEMA interface EasyTeach2 Offline Programming 2007 vintage.

Single wave system, 16" 230 VAC, 30 60 Hz, 50 AMP.

Wave Soldering Machine, 2004 vintage.

Solder wave machine Voltage : 440 V 3 Phase 2005 vintage.