Used STEAG / MATTSON / AST 2800 #9159583 for sale
It looks like this item has already been sold. Check similar products below or contact us and our experienced team will find it for you.
Tap to zoom
Sold
ID: 9159583
Single chamber RTP system, 8"
Dual load lock
Facilities / General configuration:
30L N2 High:
50psi @ Facilities, 2bar @ tool, dynamic (full N2 flow)
60psi @ Facilities, 2.8bar @ tool, static (no N2 flow)
10L O2 High:
40psi @ Facilities, 2bar @ tool, dynamic (full O2 flow)
42psi @ Facilities, 2.5bar @ tool, static (no O2 flow)
O2 Low: 40psi @ Facilities, 2bar @ tool, dynamic (full O2 flow)
42psi @ Facilities, 2.5bar @ tool, static (no O2 flow)
10L Ar:
40psi @ Facilities, 2bar @ tool, dynamic (full Ar flow)
43psi @ Facilities, 2.5bar @ tool, static (no Ar flow)
CDA:
Facilities: 90psi
Tool: 5.5 Bar
Chamber high cool:
Bottom: 17/18 m3/h
Top: 26/27 m3/h
Chamber H20 cooling:
Facilities: 6.8LPM
TC Amplifier test with omega meter:
Setpoint Feedback
1000C 1001.5
800 800.5
600 599.6
400 398.8
O2 Sensor final testing:
30L N2 flow in chamber @ 30 second: 3ppm O2
5L N2 flow in chamber @ 60 seconds: 4-5ppm O2
Robot station names:
A: Primary sender
I: Secondary receiver
F: Furnace
D: Cooling station 0
No cooling station 1
C: Dummy wafer station
Pyrometer calibration:
Un-calibrated pyrometer check: Pyro 878C output at 1080TC with emis1300
Calibration recipe: TOMCAL.2
Calibration file: TRCAL0923
Network setup:
Serial GemSecs
Expansion board: COM8
GEMBOX.INI Host: localhost
SHSCFG.INI Gembox host: localhost
RTP:
No physical dummy wafer station
MFC:
TYLAN Gas panel
TYLAN O2 Sensor
EQUIPE 307 robot
No swivel cassette stations
Gasbox above rear of tool: (supplies MFCs):
N2, N2, O2, H2Mix, Ar
Facilities connections at bottom rear of tool:
CDA: SWAGELOK 90-120PSI, 1/4"
PCWS: SWAGELOK 8slpm, 1/2"
PCWR: SWAGELOK 60-120PSI, 1/2"
PCWS: SWAGELOK, 1/2"
PCWR: SWAGELOK, 1/2"
HiFlow N2: SWAGELOK >90PSI, 1/2"
Cooling N2: SWAGELOK 10-30SLPM, 1/4"
Vent1 / Vent2 (Acid exhaust): SWAGELOK, 3/8"
11/2 Inch exhaust: 11/2 Inch tube Acid exhaust
Middle bottom of tool:
Blower output (Heat exhaust): 4" Tube
Front of tool:
House vacuum: SWAGELOK 600 mbar, 1/4"
Electrical requirements:
Power consumption: 43 kVA
Voltage: 208 VAC, 3 Phase
Current per phase: 125 A
125 Max fusable
Missing parts:
(1) Endeffector universal, 47900058
(1) Tube AST furnanec 8in, 58700001
(2) Quarts tray elbow, MATTSON Technology, 58800003
(1) Tray quarts wafer, MATTSON Technology, 58900085
(1) Plate top liner plates, LTD Materials, Inc., 11823-000
(2) Fiber optic cable IPC-ILC, 19200195
(1) Plate hotliner 8 IN, MATTSON Technology, 47800189
(1) Pyrometer AST 2800, MATTSON Technology, 17000164
(1) Controller AST Pre-Aligner, ESC-201
(1) Harddrive AST SEAGATE 160GIG, ST3160318AS
(1) ILC, PCU 2.4g SEIMENS, ILC-3
(1) Robot, ATM-307, PRI, ATM-307
(1) Pre-Aligner, 8 inch, PRI, PRE-201B
(1) Temp controller PCB
(6) IGBT
(2) Outer door panels.
STEAG / MATTSON / AST 2800 Rapid Thermal Processor is a semiconductor processing tool used for advanced applications in the electronics industry. It is designed for the production of today's advanced semiconductor chips as well as tomorrow's most demanding packages. AST 2800 is composed of two main components - the Thermal Control System and the Application Chamber. The Thermal Control System features superior temperature uniformity and temperature stability along with low thermal gradients and fast, repeatable ramp up and ramp down times. With an accurate, flexible temperature range of -160°C to 700°C, STEAG AST2800 can handle even the most delicate wafers and components. It also has precise time and temperature control capabilities, allowing for precise settings for a wide range of processes. The thermal control system is optimized for medium to high power profiles and rapid thermal cycle times, enabling higher throughput. The Application Chamber has four independently-controllable zones - bottom, top, inert, and nitrogen - and also includes process ports for the introduction of gases for environmental control. This chamber ensures pressure stability at all times and offers flexibility for varying processes. It also provides a wide range of options for loading, unloading, and handling wafers and components. 2800 Rapid Thermal Processor is ideal for advanced advanced-packaging applications, such as Cu pillar and coreless flip chip attach, and is also well-suited for high-volume production needs. With its high resolution temperature control capabilities and robust chamber design, AST2800 is the perfect tool for the most demanding chip production.
There are no reviews yet